Diamond file

This diamond grinding point is suitable for sharpening and grinding a wide variety of materials such as silver steel, HSS steel and solid carbide. Even tiles can be worked on with this diamond grinding pen. The diamond grinding point has the usual quality from Kaindl and is particularly stable. The grinding point has a diameter of 6.5mm and a length of 55mm. We recommend the diamond grinding point for re-sharpening the Kaindl Woodcarvers Gold. Since the Woodcarver is made of plasma nitrided, carbonized steel with a hardness of 62 Rockwell, it cannot be sharpened with conventional files or grinding points.

Brass Ms58 is a very good machinable material. Another advantage of brass is that it is rust-free. It is suitable for turning, milling, drilling and tapping. In addition, it can be well brazed with silver brazing and soldering. These characteristics are very much in line with the technical model builder. Most steam engines, Stirling engines and flame eaters in model making are largely made of MS58 brass. We offer you here in the Bengs Modellbau Shop brass round material in the diameter from 1mm to 50mm. Features of brass Ms58 round Round Material Brass Quality: Ms 58 (drilling and turning quality) Strength F45-50 You always get 300mm long brass Ms58 round sections. Saving set thin brass Ms 58 / You save 20% Brass round material 300mm per 1 rod 4mm 5mm 6mm 8mm 10mm 12mm 14mm 16mm Saving set thick brass Ms 58 / you save 20% Brass round material 300mm per 1 rod 18mm 20mm 22mm 30mm

3 Cutting Solid carbide cutter for even higher cutting speeds. Face cutting geometry of the solid carbide cutter is suitable for dipping. Universal cutting geometry. The solid carbide end mills can be used as a long hole and end mill. Suitable for all materials. Ideal for use in model building. Very good for steel, tool steel, stainless steel, and gray cast iron. If a solid carbide cutter breaks, do not throw it away. You can also use the Kaindl grinding technique to grind a robust and durable spike or turning steel. industrial quality   Solid carbide milling cutter Durchmesser Schneidenlänge Gesamtlänge Schaftdurchmesser 1mm 3mm 34mm 3mm 1,5mm 3mm 34mm 6mm 2mm 4mm 35mm 6mm 2,5mm 5mm 36mm 6mm 3mm 5mm 36mm 6mm 4mm 7mm 38mm 6mm 5mm 8mm 39mm 6mm 6mm 8mm 39mm 6mm 8mm 11mm 43mm 8mm 10mm 13mm 50mm 10mm

The generator can be driven via a belt by a flame eater, Stirling engine, steam engine or an internal combustion engine will be around Convert kinetic energy into electrical energy. If desired, you can also use this dynamo as a historical electric motor by simply supplying it with 12 volts. The model is based on a historical generator. The open design means you can see very well into the generator. The collector and the brusches are also outside and are very clearly visible. Of course, this generator has the obligatory eye screw in the upper part of the housing. The generator also stands on 2 tensioning rails to optimally adjust the belt tension. The complete dynamo can be moved 10 mm on the tensioning rails The material kit is mainly made of brass. The motor housing is made of aluminum. The armature with the winding and the magnets are taken from a standard electric motor included in the kit. The electric motor will be dismantled according to your instructions and some of the components will be reinstalled. Comprehensive construction instructions are included for the further steps in building the generator. In addition, you will find a detailed Construction report with lots of pictures and explanations. The generator runs very smoothly and has little resistance, making it also suitable for smaller machines with little power such as flame eaters. Accordingly, the power output is not particularly high. However, it is enough to light up a small 6 V light bulb or to operate several LEDs. All milled parts are already milled and may still need to be drilled, all turned parts are included in the kit as raw material. All required screws, nuts and the electric motor are also included in the scope of delivery. Scope of delivery generator material kit Finished milled parts Raw material for the turned parts all required screws, nuts and grub screws Construction plan generator drawings (4 sheets) and construction instructions (1 sheet) Electric motor Dimensions of generator material kit Height: 55mm Length with tension rails: 135mm Clamping rails clamping path: 10mm Width: 68mm Pulley: 10mm/16mm Performance data of the electric motor used Operating voltage: 12 V- Current consumption at maximum power: 0.56 A Power max. 2.71 W Torque: 9.95 mNm Speed: 2603 rpm