Eccentric press Nils drive model

€140.00*

Available, delivery time: 1-3 days

Product number: 2212

Product information "Eccentric press Nils drive model"

Our eccentric press is a replica of a machine tool that was used many years ago in many craft and craft industries. industrial companies could be seen. Eccentric presses were previously used for punching holes and embossing work. Originally the presses were driven via a transmission. Later Many of the eccentric presses were subsequently equipped with an external electric motor. The actual belt drive was retained. Our model is a replica of such a press. It is equipped with a punching tool with a diameter of 5.5 mm, which corresponds exactly to the diameter of an office hole punch.

The press must be powered by either a steam engine or a small electric motor. The best way to do this is to use a small round belt that acts directly on the large flywheel. The flywheel and gearbox are constantly running, but the tool is not yet moving. The model has a foot lever that operates a clutch that allows exactly one work cycle. When the foot pedal is pressed, the clutch engages and the tool moves downwards. The stamp punches the hole and then returns to its original position. Here the clutch is automatically disengaged.

Most of the model's components are made of brass. The large machine base is laser cut from steel. All axles are made of silver steel. All milled parts are included in the kit ready-machined. All turned parts are included in the delivery as raw material. Of course, as with all other Bengs model building material kits, you will also receive all the screws, nuts and springs you need.

To the construction A small lathe and a column drill are required, as well as a gas burner for soft soldering. The following should also be available:Tap M2, M3, Dies M2, M3 Reamer 5H7 files and a drill set. Otherwise, hand tools, which should be in every “technical model making workshop”, are necessary.

Here you will find an extensive construction report for the Nils eccentric press material kit with lots of pictures and tips.

Scope of delivery: eccentric press Nils drive model

Finished milled parts
Raw material for the turned parts
all required screws, nuts and grub screws
Eccentric press construction plan drawings (8 sheets) and construction instructions (4 sheets)

Dimensions of eccentric press material kit

Height: 155mm
Width: 80mm
Depth: 110mm
Flywheel: 80mm

In this video the eccentric press is powered by our generator/motor. You can find thegenerator kit here. The generator can be used to generate electricity, when connected to a power source it works like an electric motor. You can find the matchinground belt here.

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

No reviews found. Share your insights with others.

Cutsomers also bought

Ein funktionsfähiger Dynamo als Antriebsmodell

Modell Generator 2w

The generator can be driven via a belt by a flame eater, Stirling engine, steam engine or an internal combustion engine will be around Convert kinetic energy into electrical energy. If desired, you can also use this dynamo as a historical electric motor by simply supplying it with 12 volts. The model is based on a historical generator. The open design means you can see very well into the generator. The collector and the brusches are also outside and are very clearly visible. Of course, this generator has the obligatory eye screw in the upper part of the housing. The generator also stands on 2 tensioning rails to optimally adjust the belt tension. The complete dynamo can be moved 10 mm on the tensioning rails The material kit is mainly made of brass. The motor housing is made of aluminum. The armature with the winding and the magnets are taken from a standard electric motor included in the kit. The electric motor will be dismantled according to your instructions and some of the components will be reinstalled. Comprehensive construction instructions are included for the further steps in building the generator. In addition, you will find a detailed Construction report with lots of pictures and explanations. The generator runs very smoothly and has little resistance, making it also suitable for smaller machines with little power such as flame eaters. Accordingly, the power output is not particularly high. However, it is enough to light up a small 6 V light bulb or to operate several LEDs. All milled parts are already milled and may still need to be drilled, all turned parts are included in the kit as raw material. All required screws, nuts and the electric motor are also included in the scope of delivery. Scope of delivery generator material kit Finished milled parts Raw material for the turned parts all required screws, nuts and grub screws Construction plan generator drawings (4 sheets) and construction instructions (1 sheet) Electric motor Dimensions of generator material kit Height: 55mm Length with tension rails: 135mm Clamping rails clamping path: 10mm Width: 68mm Pulley: 10mm/16mm Performance data of the electric motor used Operating voltage: 12 V- Current consumption at maximum power: 0.56 A Power max. 2.71 W Torque: 9.95 mNm Speed: 2603 rpm

€63.90*

Round belt 2mm rough

Round belt for driving drive models or small machines. The drive belt has a diameter of 2 mm and a roughened surface. It is made of highly flexible PU material. You can cut the strap to the desired length and then weld it by heating it (lighter or small blowtorch) and pressing it together. These flexible but still very stable straps are ideal for model making. The drive belt is delivered as a 1 m piece. Welding the drive belt is very easy. Use either a candle or a small burner with a soft flame. Hold both ends of the strap to the flame until the plastic begins to melt. Then press the two ends of the strap lightly against each other. After the material has cooled, the excess can be removed with a scalpel or small side cutters.

€3.50*

Holder for mini boring bars

The mini drilling rods we offer fit into this holder for mini drilling rods. The holder is made of 12 mm square material and therefore also fits into steel holders on smaller lathes. The boring bars are inserted into the holder and fixed with an M4 hexagon socket screw. The holders also fit into the tool holders of very small lathes. Dimensions Holder for mini boring bars Height: 12mm Width: 12mm Length: 60mm

€23.90*

Mini drilling rods

These mini boring bars are ideal for internal turning. These internal turning tools are made entirely of carbide and have a cutting geometry that allows them to be plunged into the material without pre-drilling. This is high-quality industrial quality. The mini drilling rods are used. They were used on a CNC machine and will be replaced after a certain period of time. Only minor signs of wear can be seen. They are still very sharp and the remaining sharpness is completely sufficient for working on brass, aluminum or steel. In addition, the cutting edge can be re-sharpened relatively easily. A suitable tool holder for the boring bars can be found here. We also use these turning steels for internal turning in our workshop and are very impressed by the properties and possibilities. The following dimensions are available. Mini drilling rod 3.5x17 Minimum inner diameter: 3.5mm / Maximum immersion depth: 17mm / Total length: 30 mm Mini drilling rod 4.7x22 Minimum inner diameter: 4.7mm / Maximum immersion depth: 22mm / Total length: 35 mm Mini drilling rod 4.7x32 Minimum inner diameter: 4.7mm / Maximum immersion depth: 32mm / Total length: 45mm Mini drilling rod 5.6x22 Minimum inner diameter: 5.6mm / Maximum immersion depth: 22mm / Total length: 35mm Mini drilling rod 6.5x27 Minimum inner diameter: 6.5mm / Maximum immersion depth: 27mm / Total length: 40 mm

Variants from €5.20*

€5.60*