center punch Rennsteig

€32.50*

Available, delivery time: 1-3 days

Product number: 3516

Product information "center punch Rennsteig"

With this high-quality self-piercing center punch from Rennsteig, very small components can be easily arranged. When you apply pressure to the center punch by hand, an internal spring tensioned and exerts the force abruptly. This means that you do not need a hammer when you start the process. This type of center punch is also called automatic punch. The impact strength can be arbitrarily set for this center punch by turning the end piece as well as it has an ergonomic end piece for high user comfort.

Due to the handy size and the fine center punch tip we like to use these self-piercing center punch from Rennsteig also in our own workshop for the engraving of small parts in the technical model building.

Technical data of the self-supporting center punch

Minimum impact force 20 N
Total length 95 mm
Maximum impact force 50 N
Shaft-11 mm

automatischer-Koerner-rennsteig

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

No reviews found. Share your insights with others.

Cutsomers also bought

Verzinnungspaste zum verzinnen von größeren Bauteilen

Soft soldering paste

Soft soldering paste for brass, copper, steel and silver steel. The paste is applied thinly to the parts to be tinned and heated with a brazing lamp. For large-area soft soldering, it is optimal to tin- the parts beforehand. For example, we use the paste to pre-tine the cylinder and the mirror when constructing a model steam engine. The tinning paste can also be used optimally as a flux substitute. The soft soldering paste is excellently suitable as corrosion protection for steel parts. Bengs Modellbau uses the zinc paste for steel cylinders with a cooling water jacket. For example in the Flammenfresser Kurfürst. Stirring the paste before use is not necessary! The soft soldering paste may be diluted with water. Ready-to-use metal paste Contents: 50g Bottle with brush Click here for the modeling magazine: Soldering with soft solder paste and tin paste Soldering and tinning with soft soldering and tinning paste

Content: 0.1 Kilogramm (€102.00* / 1 Kilogramm)

€10.20*

Lötziegel als Lötunterlage bei Lötarbeiten im Modellbau

soldering brick

The white soldering brick is ideal as a soldering base for brazing and soldering in model building. The solder seal can be cut as required. In addition, soldering and holding needles can be inserted very easily into the brick in order to fix the component to be soldered. The white tiles have a relatively smooth and plane surface, through which sharp edges several bricks can be assembled seamlessly. To fix components that are to be soldered, you can simply nail into the porous material of the soldering iron. Thus, a soldering device can be produced very quickly. The soldering bricks are also suitable for the construction of a melting point. By assembling several soldering bricks, one can produce an excellent soldering place in which the gas flame of the burner can be optimally utilized. Dimensions of the brazier: 220mm x 110mm x 30mm

€8.30*

High temperature soft solder

High temperature soft solder with a melting point of 250 ° C is suitable for fittings, pipelines and components on steam engines, Stirling engines and flame eaters. The soft solder is filled with a flux that burns without residue when flame brazing (flux residues must be removed in the case of piston soldering !!!). If you need additional flux, you can use normal soft solder flux. Due to the increased melting point of 250 °, it is a good alternative to brazing. However, the high-temperature softening braze can not replace brazing. This product should not be used in the vicinity of the boiler. The use of silver solder is recommended. Wire diameter: 1mm Wire length: 1000mm This product is unleashed !!!

€2.40*

Center punch set

The center punch set consists of 25 center punches made of hardened steel. The center punches are suitable for transferring holes from one component to another. To do this, a centering center punch is inserted either into the hole of an existing component or into the hole of a template and transferred to the second part. The center punch set is suitable for use in mechanical engineering, steel construction, crafts and hobbies. The grain diameters increase by 0.5mm from 1mm to 13mm. The actual dimensions of the center punches are 0.05mm below standard dimensions. All 25 center punches are 120mm long. The center punches are delivered with a clear metal stand. Centering center punch set (25 pieces) from 1mm to 13mm 0.5mm increments

€31.30*