Powderoven M54x60x90cm

With this powder you can powder coat components with a chrome-like look. The powder is processed in the same way as our standard powders. It is first applied with the Power Coat 4 PRO powder gun. Unfortunately, processing with our small powder gun is not possible. After application, the powder is baked at 180°C. After the component is in the oven, wait until the chrome powder begins to shine, then the components should be baked in the oven for another 15-20 minutes. After cooling, the powder-coated part is immediately ready for assembly or further processing. The surface of the powder runs very smoothly, even small unevenness in the material is evened out by the powder. Compared to real chrome, the shine here is a little milkier. Without an additional clear coat layer, the powder coating is relatively sensitive. An additional layer of clear varnish coating powder significantly increases the mechanical strength, but also reduces the mirror effect. This makes the chrome shine even milkier. If the parts are only for decoration or are only subject to minimal mechanical stress, you can do without the clear coat. However, if the load is higher, the powder should definitely be covered with clear varnish. The coating powder is filled into plastic buckets so that the powder remains permanently dry. Here you will find standard colors RAL Powder coating in our shop.

You will get powder coating powder in facade quality in 250g bottles. The coating powder is filled into plastic bottles so that the powder remains permanently dry. With the powder you can create an easy to clean, weather and UV-resistant and extremely durable surface coating. The powder is suitable both for powder coating with corona and with tribo coating devices. The coating powder has excellent light and weather resistance. It also has a good elasticity so you can even coat feathers. The powder adheres to all surfaces. All powder coatings available at our company are suitable for corona powder coating systems as well as for tribo powder coating systems.  The following coating powder colors are available: RAL 1003 Signal Yellow Glossy (250g) RAL 3000 Fire Red Glossy (250g) RAL 5005 Signal Blue Shining (250g) RAL 6020 Chromium oxide green Glossy (250g) RAL 7001 Silbergrau Shining (250g) RAL 7016 Antrazite Gray Glossy (250g) RAL 9005 Deep black Glossy (250g) RAL 9005 Deep black Deep matt (250g) RAL 9010 Pure White Glossy (250g) Transparent colorless high gloss (250g) Chrome Metallic Gloss (250g)  

The Power Coat 4 PRO is a high-quality powder coating system for small to large areas. You will receive the powder coating gun in a high-quality plastic case in which everything has its place. This powder gun is significantly more robust than our standard powder coating system. This makes it suitable for use in commercial businesses and for ambitious DIY enthusiasts. Advantages of powder coating over painting: Ready to use immediately without drying time Extremely robust and abrasion-resistant Optimal corrosion protection Environmentally friendly as no solvents Absolutely uniform surface quality Coating remains elastic e.g. for springs The Power Coat 4 PRO has a 500 ml powder container so that even larger areas can be coated with powder without having to refill the coating powder in the meantime. Another advantage of this device is that there is a water separator and a pressure regulator directly on the powder gun. This makes setting the correct pressure much easier. Scope of delivery: Powder coating device with Schuko earthing plug, stable ground clamp, water separator and pressure regulator Two 500ml powder containers to screw into the coating gun Funnel for easy filling of the powder containers Sturdy case for storage 14 pages German operating instructions The Power Coat 4 PRO powder coating device is suitable for many different powder coating applications. With this powder coating system, even the smallest components can be easily powder coated. Even larger parts are no problem thanks to the 500 ml powder container. Our powder coating systems are very often used in the restoration of old motorcycles or cars. With this system it is possible to coat entire motorcycle frames or rims with powder varnish for coating. The result is indistinguishable from industrial powder coating. Powder coating is also very often used in technical model making because the finished surface is extremely robust, scratch-resistant and provides good corrosion protection. Application examples powder coating of vintage car parts Powder coat motorcycle parts Powder coat rims Powder coating of small parts in technical model making This powder gun is a Tribo powder coating system. The powder becomes statically charged in the barrel of the gun due to the friction on various materials. The device is connected to the earth conductor of the socket via a ground terminal and a Schuko plug, which means the component is grounded. Due to the electrostatic charge generated during the run, the coating powder adheres to the workpiece. This effect allows you to coat a variety of materials. The charging occurs when the powder particles touch the wall of the barrel of the powder gun, causing electrons to be released from the Teflon™ barrel. The powder paint particles are separated from the spray gun faster than the charge can be redistributed. This means that the powder particles remain charged and stick to any material. You do not need any additional electricity for the tribo process. The included plug is only the ground connection of the device. Power Coat 4 PRO can process all coating powders that are suitable for Tribo systems. Here in our online shop you will find suitable spare parts for the powder coating system. p> Coating wood, tiles and glass In contrast to conventional powder coating systems, this powder gun coating system can also be used to coat wood, tiles and glass. Since these materials are not conductive, the ground terminal cannot be connected here. This makes applying the powder a little more difficult. You should first make a sample to test the properties of the material and its behavior during powder coating. What else is needed (not included) Compressor Extension hose oven for burning (min. 200c ° from a small household oven to our)