This tube is a hydraulic cylinder tube. The inside of the tube is very dimensionally stable and wear-resistant. The cylinder tube is suitable as a cylinder sleeve for an internal combustion engine or flame eater. We also use this cylinder tube in our models. We use it for the combustion engine Karl, Stirling engine "Big Laura" and the Flame Eater Jarne. Due to its high wear resistance, the tube has proven itself as a cylinder sleeve for us.
Dimensions of hydraulic cylinder tube 25mm:
Outer diameter: 35mm
Inner diameter: 25mm
Length: 83mm
Material: St52
Suitable Piston ringsfor this cylinder tube can be found here
Dimensions of hydraulic cylinder tube 30mm:
Outer diameter: 40mm
Inner diameter: 30mm
Length: 86mm
Material: St52
Dimensions of hydraulic cylinder tube 40mm:
Outer diameter: 50mm
Inner diameter: 40mm
Length: 117mm
Material: St52
Dimensions of hydraulic cylinder tube 50mm:
Outer diameter: 60mm
Inner diameter: 50mm
Length: 142mm
Material: St52
Brass Ms58 flat material is a very good machinable material. Brass is probably the most widely used material in technical modeling. Which is certainly due to the fact that it can be worked very well. It can be milled, turned, drilled, brazed and softened. Many Stirling engines, steam engines and flame eaters in technical model construction are mainly made of MS58 brass. You can order brass flat material in different thicknesses from 2mm to 6mm here at the Bengs Modellbau Shop.
Flat Material Brass Quality: Ms 58 (drilling and turning quality)
Strength F45-50
Flat material 50mm wide
Length 300mm
These relatively small spark plugs are particularly suitable for model combustion engines. Its metric M10 × 1 thread also fits into smaller cylinder heads. The spark plugs fit into our internal combustion engine and can be used as a spare part. Of course, you can also use the spark plug CM-6 for your own development with our ignition components.
Data of spark plug CM-6 M10x1
Key range: 14.0 mm
Overall length: 36mm
External thread: M10x1
Thread length: 8.6 mm
Cast iron with lamellar graphite. The surface is peeled on the gray cast iron bars. The round bars are a little over-sized. You can also make a 30mm piston with a 30mm diameter. The material is suitable both for the production of pistons or cylindrical sleeves for model-built motors as well as for the production of plain bearing bushes. We use this material for the pistons at the station "Karl". The round material can be perfectly machined on the lathe and on the milling machine and has excellent running characteristics.
All round bars are 300mm long.
Brass Ms58 is a very good machinable material. Another advantage of brass is that it is rust-free. It is suitable for turning, milling, drilling and tapping. In addition, it can be well brazed with silver brazing and soldering. These characteristics are very much in line with the technical model builder. Most steam engines, Stirling engines and flame eaters in model making are largely made of MS58 brass. We offer you here in the Bengs Modellbau Shop brass round material in the diameter from 1mm to 50mm.
Features of brass Ms58 round
Round Material Brass Quality: Ms 58 (drilling and turning quality)
Strength F45-50
You always get 300mm long brass Ms58 round sections.
Saving set thin brass Ms 58 / You save 20%
Brass round material 300mm per 1 rod
4mm
5mm
6mm
8mm
10mm
12mm
14mm
16mm
Saving set thick brass Ms 58 / you save 20%
Brass round material 300mm per 1 rod
18mm
20mm
22mm
30mm
This brass Ms58 hexagonal material is very easy to machine and is ideal for turning, milling, drilling and tapping. The material is suitable for self-assembly of screws, model building nuts and other components for technical modeling. You can order different key sizes in our shop, or you can order a set of different diameters.
Features of brass Ms58 hexagon
Hexagonal material brass with different key ranges
Quality: Ms 58 (drilling and turning quality)
Strength F45-50
Length: 300mm
We supply the brass Ms58 hexagon in 300mm sections.
Savings set Hexagon brass Ms 58 / You save 20%
The brass hexagonal material savings set includes 300mm per 1 bar
4mm
5mm
6mm
8mm
10mm
12mm
The Ignition condenser for intermittent ignition is a component which should not be missing. The condenser regulates the strength of the ignition spark. This ignition coil is also installed in the internal combustion engine Karl and can be used as a spare part. You can use this capacitor to create an ignition breaker for model building. This is a solid moped technology that has proven itself over many years. An intermittent ignition is very durable and also times a wrong polung.
Dimensions Capacitor for Ignition condenser
Length: 41mm
Diameter: 18mm
Threaded connection: M4
Use this Ignition interrupter to generate the spark. You can control the breaker directly via a cam or via a ram. This article is a serial product from the moped technology. This guarantees a good quality, long durability and fast availability. You can create your own ignition system from this interrupter. We also use this breaker in the ignition of our internal combustion engine "Karl". It can also be used as a spare part in this model.
Dimensions of the Ignition interrupter
Length: 30mm
Width: 30mm
Height: 20mm
This ignition coil is suitable for installation in an intermittent ignition. This ignition coil is also installed in the internal combustion engine Karl and can be used as a spare part. In the normal case, this coil is used for ignition in mopeds. However, due to its reliability and performance, it is very well suited for model construction. An intermittent ignition usually works very reliably and can be more easily checked for faults than an electric ignition.
Dimensions of ignition coil 12V intermittent ignition
Length: 123mm
Diameter rear: 40 mm
Largest diameter collar: 48 mm
Connection thread: 2x M4
Square brass in different diameters. This brass is very good machinable and suitable for turning, milling, drilling and tapping. Square braces, fork heads and other components for technical modeling are very well suited to be manufactured from square material.
Features of brass Ms58 square material
Quality: Ms 58 (drilling and turning quality)Strength F45-50
We supply the brass Ms58 square material in 300mm sections.
Saving set square brass Ms 58 / you save 20%
The brass square material savings set contains 1 rod 300mm long
4mm
5mm
6mm
8mm
10mm
Here you will find a toggle switch with which you can start and stop the ignition of your model motor. The toggle switch is designed both mechanically and electrically robust. We also use this toggle switch for the inflammation of our internal combustion engines. Thanks to the classic design, the toggle switch fits well with the most varied model-motor.
Switching capacity 10 A / 250 V ~
1-pole
Execution ON / OFF
Operating temperature -25 ... + 85 ° C
Switching cycles> 10,000
Mounting Ø 12 mm
screw
Overall dimensions without shield (LxWxH): 29x16x53 mm
Hier können Sie Ersatzteile für Ihren Stationärmotor Karl bestellen. Alle Frästeile sind wie im Bauplan nummeriert. Alle Frästeile für den Verbrennungsmotor werden von uns aus MS58 auf einer CNC Fräse ausgefräst. Bitte entnehmen Sie die benötigte Stückzahl der Stückliste vom Stationärmotor Karl. Der Preis bezieht sich immer auf ein Stück.
Ersatzteile Frästeile Stationärmotor Karl
Teil 2 / 1 Stück Seitenwange Rechts MS58 112mm x 40mm Frästeil
Teil 3 / 1 Stück Seitenwange Links MS58 112mm x 40mm Frästeil
Teil 4 / 2 Stück Lagerdeckel Kurbelwelle MS58 36mm x 11mm Frästeil
Teil 5 / 1 Stück Lagerdeckel Nockenwelle MS58 21mm x 6mm Frästeil
Teil 8 / 1 Stück Zylinderhalter MS58 56,5mm x 50mm Frästeil
Teil 13 / 1 Stück Kipphebel Auslass MS58 35mm x 8mm Frästeil
Teil 15 / 1 Stück Kipphebelhalter MS58 35mm x 24mm Frästeil
Teil 17 / 1 Stück Hintere Gestellstrebe MS58 47mm x 8mm Frästeil
Teil 27 / 2 Stück Kurbelwange MS58 50mm x 60mm Frästeil
Teil 34 / 1 Stück Nocke Auslass MS58 16mm x 4,80mm Frästeil
Teil 35 / 2 Stück Stößelführung Seitenplatten MS58 35mm x 12mm Frästeil
Teil 38 / 1 Stück Lagerbock Stößelführung MS58 18mm x 10mm Frästeil
Teil 39 / 3 Stück Lagerbock Nr 4. MS58 18mm x 9mm Frästeil
Teil 42 / 2 Stück Reglerarm MS58 37mm x 10mm Frästeil
Teil 44 / 1 Stück Reglergestell MS58 41mm x 28mm Frästeil
Teil 49 / 1 Stück Reglerhebel MS58 65mm x 16mm Frästeil
Teil 57a / 1 Stück Zahnrad Nockenwelle MS58 43,88mm x 3mm Frästeil
Teil 58a / 1 Stück Zahnrad Kurbelwelle Ms58 22,4mm x 3mm Frästeil
Teil 71 / 1 Stück Tankanzeige MS58 23mm x 15,5mm Frästeil
Teil 79 / 1 Stück Kondernsatorhalter MS58 30mm x 30mm Frästeil
Machine base made of gray cast iron for the stationary engine Karl. If you need a replacement machine base for the Karl stationary engine, you can order it here in our model making shop. The machine base corresponds to the original base that is included with the material kit for the stationary motor.
Dimensions of machine base stationary motor Karl
Weight: 2.20kg
Length: 190mm
Width: 95mm
Height: 60mm
Material: GG25
€72.60*
This website uses cookies to ensure the best experience possible. More information...